How do I light my Traeger wood pellets?

How to Start and Ignite a Traeger Pellet Grill

How do you get wood pellets to light?

  1. Fill the stove’s hopper with wood pellets. .
  2. Open the burn pot door and add accelerant to the wood pellets. .
  3. Hold a long-reach butane lighter, like those used to light gas fireplaces or grills, near the pellets and light it.

What lights the pellets in a Traeger grill?

Traeger grills use electricity to power the auger the feeds real hardwood pellets to the fire and the fan that circulates heat and smoke to ensure consistent results. The fire in a Traeger grill is fueled by 100% all-natural hardwood pellets.

Can I manually light my pellet grill?

Manually Lighting A Pellet Grill

How do you light a wood pellet basket?

Simply place the basket in your wood stove, fill it with wood pellets, light the pellets with gel fire starter. Add more pellets, when needed. Scoop the hot pellets to one side with a metal scoop, add new pellets next to the hot pellets. The hot pellets will ignite the new pellets.

How do you start a wood pellet without a torch?

I simply take an old shot glass, fill it with pellets then pour just enough 91% alcohol to cover the pellets. I let them soak for about 5 minutes while I prep the BBQ.

Can you use lighter fluid to light wood pellets?

NEVER light or rekindle fire with kerosene, gasoline, or charcoal lighter fluid; the results can be fatal.

How do you ignite pellets in a smoker?

How to Light a Pellet Grill | Grillabilities from BBQGuys

How does a pellet grill ignite?

  1. Pellets feed by gravity from the hopper to the auger.
  2. Pellets move along the auger as it rotates toward the burn pot.
  3. As pellets fall into the burn pot, the Hot Rod burns the pellets to start combustion.
  4. The fan blows in air to create flames and intensify the fire.

Why is my Traeger not burning the pellets?

Traeger Grills – Troubleshooting: Grill Startup

Why is my pellet grill not lighting?

The most common reason a Traeger won’t ignite is a dirty Fire Pot. Confirm your Fire Pot is clean, then make sure the hot rod is producing heat. If it isn’t, replace it. If it is, adjust the hot rod so that it comes out further, towards the center of the Fire Pot.

What to do when Traeger failed to ignite?

  1. Check to make sure there are pellets in both firepot and in the hopper. If empty or low, fill the hopper.
  2. Check to ensure the lid was kept close during start-up.
  3. Ensure the pellets being used are good. Pellets should have a shine to them and snap when broken.

How long does it take pellet grill to heat up?

You can quickly get a gas grill up to your desired cooking temperature. Firing up a pellet grill is a little more of a process. You fire the grill up with a press of a button but it takes around 10 to 15 minutes to get up to your selected temperature.

How long does it take for Traeger to heat up?

With the lid open, set your Traeger grill to the SMOKE setting. You will hear the fan running. Wait roughly 5 minutes for the fire to ignite and establish. You will hear a difference in the fan once the flame gets rolling.

Why isn’t my pellet smoker getting up to temp?

Not having enough pellets in the hopper, or even having old/poor quality pellets, can cause temperature issues or the flame to go out. Check the pellet level in the hopper. If you’ve run out of pellets or notice some tunneling, learn more here.

Why does the fire go out on my Traeger?

Fire Goes Out During Cooking

Low-quality pellets, which produce too much ash, are the primary suspect. Excess ash can extinguish a fire, even in the middle of the cooking process. The RTD probe might also be giving bad information to the controller, causing it to feed a lower number of pellets into the firepot.

How do you unclog a Traeger Auger?

Traeger Grills – Troubleshooting: How to Clear a Jammed Auger

Why does my Traeger smoke so much when igniting?

If there is an excessive amount of smoke coming out of the hopper, this is due to active backburn (pellets burning in the auger causing excessive smoke). Customers actively experience this should be advised to do the following: Unplug the grill. Keep both the grill and hopper lid closed to starve the fire of oxygen.

Where is the hot rod on a Traeger grill?

Traeger Grills – Troubleshooting: How to Replace the Hot Rod

Can I use Traeger pellets that got wet?

As you can see, the water expands the pellets and breaks them down into their original state of sawdust. If pellets have expanded after moisture contact, they are not usable in your pellet stove.

Do you ignite Traeger open or closed?

Open-Lid Startup Process

When ready to cook, ensure all your internal grill components (heat baffle, drip tray, grill grates) are inside the grill. Set your Traeger grill to the SMOKE setting with the lid open. You will hear the fan running. Wait for the fire to ignite and establish, roughly 5 minutes, give or take.

Do you shut down Traeger with lid open?

Traeger Grill Shut Down Cycle – Traeger Maintenance

Do you have to light a Traeger?

Plug your grill into an electrical outlet.

Unlike traditional wood-burning grills, Traeger equipment requires power to operate the internal thermostat, fan, igniter rod, and wood pellet auger. To avoid starting the grill accidentally, leave it unplugged when not in use.

How do you preheat a pellet grill?

Grilling Tips with Grill Guy Jeremy – Preheating Your Traeger Grill

Do you close the lid after lighting charcoal?

SHOULD I OPEN OR CLOSE MY GRILL LID WHEN STARTING CHARCOAL? The lid should be open while you arrange and light your charcoal. Once the coals are well-lit, close the lid. Most charcoal grills are hotter right after lighting.


Related Videos

Traeger Pellet Grill and Smoker Initial Firing Instructions

Initial Firing | Traeger Grills

Manually Lighting A Pellet Grill


Related Articles

How do you hook up a propane grill?

Why is BBQ sauce sweet?

Can you use vinegar to clean a griddle?

Is BBQ a Texas thing?

How do you cook hamburgers on a flat top grill?